|
Log Home Products
How Much Do I Need?
Technical Advice
Newsletter
|
UV Guard II Clear- Sample
|
|
Availability: In-Stock
Shipping Time: 3-5 Business Days
Warranty: Limited
Description:
UV GUARD II was developed for use as an exterior wood finish for log homes and quality wood siding. It is also very effective when used as a coating on fences, shingles and other vertical surfaces. UV GUARD II is also safe to use on interior wood surfaces and is especially good for areas that receive extra amounts of sunlight. Do not use on high density, high oil content or exotic woods. UV GUARD II is an exterior acrylic wood finish that contains highly advanced UV absorbers and stabilizers. These unique and effective additives give greater protection and longevity to wood surfaces that are continuously exposed to the harmful and destructive ultraviolet rays of the sun. Stringent testing during which UV GUARD II was subjected to high levels
of sunlight, moisture and temperature extremes proved that UV GUARD II
lasted longer and provided greater protection than major competitors.
Note: We do not recommend that clear UV GUARD II be used as the only exterior coating. While UV GUARD II will add longevity and protection to exterior wood surfaces, pigmented exterior finishes will provide even greater protection. In addition to the ultraviolet absorbers and stabilizers, the pigment particles themselves help to block the rays of the sun. Clear UV GUARD II should only be applied as the “finish coat” after at least one (1) coat of a stain color has been applied, or as a “maintenance coat” to brighten and reseal a previous finish.
|
|
Stain Application Tips:
- Plan to stain when the forecast is predicting
good weather that will extend 1-2 days after the stain has been applied.
- The moisture content of
wood should not exceed 19%.
- Log surfaces must
be sound and clean from dirt, pollen and
other surface contaminants.
- Surface prep should be done no
more than 1-2 weeks before stain is applied. Media blasting and other
dry prep methods are best, but power washing can work if done properly
and the wood is allowed to dry.
- Apply
to log surfaces with a temperature range of 40°F (4°C) and rising to
90°F (32°C) and falling.
- Do not apply to surfaces in direct
intense sunlight, since the surfaces can be too hot.
- If your home is in an area of high humidity, add additional mildewcides to the stain. Call us for recommendations.
- Mix
together pails that may have different lot numbers; this will help
ensure uniformity of color. Stir thoroughly to mix all pigments evenly,
and stir the stain periodically throughout application.
- Brushing the stain into your wood will help promote better adhesion thus giving your stain more durability.
- Spraying your stain followed by brushing is a good way to speed up the process. It is important to flood the surface of your wood while spraying.
|
- How often do I need to restain my log home?
- A good stain should last between 2-3 years on the southern exposure of the home and 3-4 years on the other sides of the home.
- What is the difference between oil based stain and water based stain?
- Oil
based stains have a strong odor, are user friendly, produce a natural
looking finish and require the use of solvents during the clean-up
process. Water based stain products are environmentally friendly, odorless but
can be a little more difficult to apply.
- What steps should I take before staining my log home?
- 1.) Make sure your logs are clean and sound.
- 2.) Make sure the surface temperature of the logs are between 50-90 degrees.
- 3.) Make sure the weather forecast is dry for two days during the
staining process and dry for a two days after the staining process.
- 4.) Make sure the moisture content of the wood is below 20% prior to the staining process.
- 5.) Make sure that you don’t have any compatibility problems with any previously applied coatings.
- 6.) Read all of the application guidelines for the stain material that is being applied.
- 7.) Recommendation: Use a sprayer to flood the surface of the logs with
the stain material and then immediately back brush the stain into the
pores of the wood.
- Do your stains contain a mildewcide?
- Most stain products have a standard amount of mildewcide in
them. We recommend adding an additional mildewcide packet if you live
in an area that is prone to high humidity and high temperatures. We
sell a mildewcide additive called Stayclean I/E.
- Is the UV protection in the stain or clear coat?
- The stain has a combination of pigments and UV-absorbers while the clear coat only has UV-absorbers.
|
Available Colors
UV GUARD II is available in Cedartone, Slate Gray, Golden Wheat, Santa Fe Sun, Teakwood, Rustic Timber and Clear. Custom colors are also available.
Physical Properties
Viscosity 175-200 cps
Density 8.5 +/- 0.1 lbs./gal.
pH 8 +/- 0.5
VOC Less than 50 g/l
% Solids 25%
Odor Odorless when dry
Toxicity Non-toxic/safe for interior
Shelf Life 2 years
Stability Salt spray stable
Test Method ASTM G-53
Coverage
Coverage will vary depending on type and texture of wood surface.
Dry Time
UV GUARD II will be dry to the touch in 30 minutes to 1 hour and completely dry in 24 to 48 hours depending on temperature and relative humidity.
Packaging
UV GUARD II is available in 5 gallon and 1 gallon pails.
Storage
Store UV GUARD II in a tightly sealed container in moderate temperatures (between 40° F. and 90° F.) DO NOT FREEZE.
Clean Up
Clean up immediately with soap and water. Dried brushes will require cleaning with lacquer thinner. Spray equipment should be cleaned immediately per the equipment manufacturer’s recommendations for latex finishes. Dispose of excess materials and UV GUARD II by following all local, state and federal environmental disposal regulations.
Application Guidelines
READ AND FOLLOW ALL LABEL INSTRUCTIONS PROIR TO APPLICATION OF THIS PRODUCT.
Note
Never apply stains without first doing brush out samples.
|
|
If you find an identical item priced lower at a different online store, Mountain Home Building Products will
MATCH their price and GIVE YOU $10 off your next order.
Proof of the competitors price including shipping and handling fees must be provided via email or communicated with one of our representatives.
|
|
|
Shopping Cart
